This module is used to initialize and setup a STMicroelectronis LSM6DSL. For testing I used a NUCLEO-STM32F401 + X-NUCLEO-IKS01A2. LSM6DSL
The IKDS01A1 shield includes the following sensors:
This module require the following resources:
In this example the Sensor is enabled in normal operating mode, with interrupt enabled. Speed is slow (12.5 Hz). It is a good idea to use a low frequency. If interrupts are used keep in mind, that a higher frequency will cause a high interrupt load.
If no settings are used for the enable function the following default configuration is used:
I2C1.setup({scl:B8,sda:B9, bitrate:400000});
var MyLSM = require("LSM6DSL").connect(I2C1);
MyLSM.enable({interrupt:true, mode:"slow", sensor:"gyro"});
To verify our configuration we can use the logReg function. This function will dump all relevant register values, including configuration and status registers to the serial interface. This function is intended to be used only during development.
MyLSM.logReg();
The sensor data is read and stored in object variables. There exist three functions to read out sensor data.
Keep in mind: Read only required data, this reduce the time required to read the data. This approach is choosen, since this allow it to implement more complex allgorithm in the library. Also it is faster to store the data, then to return data which is not used.
MyLSM.update();
MyLSM.updateG();
MyLSM.updateXL();
The sensor data is read and stored in object variables. Return value is in g for the Accelerometer and Degree (Change) for the Gyro. Currently calibration is not implemented, therefore you have to take care about the drift. Also it seems that Degree is not exact what is expected.
Keep in mind: Read only required data, this reduce the time required to read the data.
print("XL_X: " + MyLSM.XL_X);
print("XL_Y: " + MyLSM.XL_Y);
print("XL_Z: " + MyLSM.XL_Z);
print("G_X: " + MyLSM.G_X);
print("G_Y: " + MyLSM.G_Y);
print("G_Z: " + MyLSM.G_Z);
This example configure the LSM6DSL and enable the interrupts. The push button on the Nucleo Board is used to turn on and of reading of results. Since the LIS6DSL waits for the next measurement until the previous value is read this allows us to start and stop the sensor. As you can see it is also required to read the sensor at the beginning to start first measurement.
Please be aware that his example will not work from flash. Use the E.init() function for configuration if it should run from flash.
To start the sensor press the push button on the Nucleo Board.
// LSM6DSL Example
// Change Ports if you use another Board!
I2C1.setup({scl:B8,sda:B9, bitrate:400000});
var MyLSM = require("LSM6DSL").connect(I2C1);
var RunMode = false;
MyLSM.enable({interrupt:true, mode:"slow", sensor:"gyro"});
var result = MyLSM.GetID();
print( "ID: " + result);
function io_interrupt ( )
{
if ( RunMode === true )
{
MyLSM.update();
print("X: " + MyLSM.XL_X + " Y: " + MyLSM.XL_Y+ " Z: " + MyLSM.XL_Z);
}
}
function io_RunMode ( )
{
if ( RunMode === true )
{
RunMode = false;
print ("off");
} else {
print ("on");
RunMode = true;
MyLSM.update();
}
}
setWatch(io_RunMode, BTN,
{repeat:true, edge:"rising"});
setWatch(io_interrupt, B5,
{repeat:true, edge:"rising"});
This page is auto-generated from GitHub. If you see any mistakes or have suggestions, please let us know.